Views: 0 Author: Site Editor Publish Time: 2026-11-17 Origin: Site
6DOF (Six‑Degree‑of‑Freedom) Stewart motion platform is a typical parallel kinematic equipment. It realizes 3‑axis linear movement and 3‑axis rotational movement through the synchronous telescoping of six servo electric cylinders. Widely adopted for driving simulators, flight simulation, vehicle performance testing and laboratory dynamic test benches.
A complete working 6DOF platform is not only a set of mechanical frames and actuators. It integrates mechanical motion mechanism, electrical drive system and software control system working closely together. Below we walk through its hardware composition, key technical requirements and basic selection principles.
The whole 6DOF platform can be divided into three major subsystems: motion mechanism system, electrical system and software control system.
This is the mechanical body of the Stewart platform:
Upper platform: Movable top mounting plate for installing cabins, test fixtures or simulation equipment;
Lower base platform: Fixed bottom foundation frame bearing the whole system weight;
Servo electric cylinders: Six sets of servo actuators as driving struts to generate linear push‑pull motion;
Spherical hinge joints (Hooke joints): Transmission connecting parts between electric cylinders and upper / lower platforms, compensating angular offset during platform tilting.
Responsible for power supply, drive and real‑time signal feedback:
Controller: PLC or motion control card for kinematics calculation and motion task scheduling;
Motor drivers: Support EtherCAT bus high‑speed synchronous communication for six actuators;
Servo motors with absolute encoders: Provide closed‑loop position feedback to guarantee positioning accuracy.
Realizes human‑machine interaction and motion algorithm solving:
Host computer (Upper PC): Human‑machine interface for parameter setting, status monitoring and command sending;
Control algorithm: Forward & inverse kinematics solving for the 6‑axis parallel mechanism.
Before customizing or quoting a 6DOF platform project, customers need to provide core technical parameters, which directly determine platform configuration, actuator specification and control scheme. We classify requirements into four groups.
Effective payload: Max weight the upper platform needs to carry (cabin, operator, test fixtures);
Platform dimension & site layout: Length × width × height limits of platform and installation space.
Payload and dimension will decide platform overall configuration and the model of servo electric cylinders.
Includes displacement, velocity and acceleration for all six axes:
Translation (X‑Y‑Z axis): Surge, sway, heave — linear displacement, linear speed, linear acceleration;
Rotation (α‑β‑γ axis): Pitch, roll, yaw — rotational angle range, angular velocity, angular acceleration.
These dynamic indexes define servo motor selection and platform mechanical specification.
Power supply condition: 3‑phase 380V or 3‑phase 220V;
Power limitation: Whether there is upper limit for total system power consumption.
Special demands for customized functions, secondary development interfaces or algorithm modification should be clarified in the early‑stage design phase.
Typical parameter reference table for your project reference
We provide multiple standard 6DOF platform models covering different payload ranges:
6DOF‑044: ≤100 kg
6DOF‑065: ≤500 kg
6DOF‑075: ≤1000 kg
6DOF‑095: ≤3000 kg
6DOF‑110: ≤5 T
6DOF‑135: ≤10 T
6DOF‑180: ≤25 T
6DOF‑270: ≤100 T
General selection principle under normal‑condition motion indexes:
For high‑dynamic scenarios: displacement ≤500 mm, linear speed ≤500 mm/s, linear acceleration ≤0.5 g, angular velocity ≤50°/s, angular acceleration ≤90°/s², you can directly select the corresponding model by payload.
For medium‑dynamic scenarios: displacement ≤250 mm, linear speed ≤250 mm/s, angular velocity ≤30°/s, angular acceleration ≤60°/s², payload‑matched standard models work well.
If your dynamic requirements exceed above normal ranges or you have strict dimension constraints, please consult our engineering team for customized calculation and solution.
A reliable 6DOF Stewart motion platform relies on matched mechanical structure, stable electrical drive and mature kinematics control software. For new projects, sorting out payload, installation dimension and full six‑axis motion parameters in advance will greatly speed‑up solution evaluation.
If you are looking for 6DOF motion platform solutions for driving simulation, training equipment or dynamic test benches, please contact our engineering team for technical consultation and model recommendation.